Florida Eco Products

Chilipepper water pump CP6000. From the time the hot water tap is turned on, to the time hot water actually arrives, thousands of gallons are wasted down the drain.

Chilipepper CP6000 pump eliminates water waste and saves time by recirculating the initial cool water back through your existing cold water line. When the water at your tap is the desired temperature, the Chilipepper turns itself off. Then turn the hot water tap or shower on and get instant hot water - with no waste.

Chilipepper pump CP6000 can be activated by a push switch (included), by wireless remote or set up on a timer with the optional upgrades. Chilipepper is compatible with all modern hot water systems, including tankless .
Chilipepper costs about $2 per year to run.

How the Chilipepper hot water pump works.

At the touch of a button, the Chilipepper pumps hot water from your water heater to your sink, or shower, while sending the cooled off hot water back to the water heater through the cold water piping. A great home improvement product.

State of the Art Electronics

The Chilipepper CP6000 instant hot water pump is a small powerful micro-processor controlled pump that installs under your sink. The brain of the Chilipepper is a tiny computer on a chip.

The computer monitors the temperatures, timing, sensitivity adjustment input, and the control wire inputs and directs the pump what to do and when.

When you push the start button, the Chilipepper CP6000 pumps the water in a big loop from the water heater through the hot water piping to the Chilipepper, and on through the cold water piping back to the water heater inlet.

When the electronic control circuitry detects an increase in the water temperature inside the pump of from 3° to 12° F, it shuts the pump off.

The shut-off sensitivity is adjustable with a knob on the front of the Chilipepper.  Turning the knob clockwise will result in hotter water at the fixture when you turn it on.

When the circuitry detects a temperature over 96°.F it locks out the pump until the water in the pump cools back down to below 96°F.  If you try to start the pump while the water is over 96°F, then the pump will run for 1/4 second and shut off, to let you know the water is already hot.

To start the Chilipepper pump  a momentary contact is required.  This can be provided by the push button included with each Chilipepper CP6000 , or an X-10 UM506 universal remote receiver and remote transmitter can be used for remote operation.

The motor is a 250-watt brush-type 1/3 horsepower motor with a built-in automatic-reset temperature limit switch, ball bearings, and stainless steel armature shaft, custom manufactured for Chilipepper Sales.

The pump head is a centrifugal  type pump, that in combination with the above motor will pump approximately 2-1/2 to 3 gallons per minute in a typical residential plumbing system.

When the Chilipepper pump is connected to a typical residential plumbing system it pumps water at a rate of  about 50 feet in 20 seconds with 1/2 inch copper pipe.  

The Chilipepper CP6000 pump has the most advanced state of the art electronic circuitry in the industry with the following features:

• Turns off automatically when the hot water reaches the pump.

• Chilipepper pump won't start if the water temperature in the pipe is over 96 degrees.

• If hot water doesn't arrive within 3 minutes, the pump shuts off. This is a safety feature that protects against the pump running forever if there is a water heater failure.

• If a short occurs on the control wires because of a button or remote malfunction the pump will cycle on for 1/4 second every 15 seconds until the problem is resolved.

 Why buy the Chilipepper CP6000:

1 Get your hot water faster - less waiting
2 Save thousands of gallons of water per year
3 Quick easy installation
4 Improves the performance of your dishwasher
5 Saves energy
6 Reduces sewage output...easier on septic systems
7 Reduces greenhouse gas emissions
8 1 Year full Manufacturer warranty plus 4 years pro rated manufacturer warranty

Your Chilipepper pump Model CP6000 includes:

The Chilipepper Appliance
A push button
Two brass “T” fittings
Two brass thread adaptors
One brass hose adaptors (Not Attached)
One washer for hose adaptors (Not Attached)
Three black plastic check valve spacers 

*   In Addition to the Above, you will need to purchase four Stainless Steel (SS) hoses (SS is not required but recommended) with cone style washers, two for connecting the T fittings to the shut-off valves, and two for connecting the Chilipepper to the T fittings. The T fittings are  3/8” OD Comp and the Chilipepper fittings are 1/2” FIP. The length and thread size of the hoses needed to complete the installation depends on the shut off valves under the sink.

(Optional remote control units are not manufactured by Chilipepper but are X10 products and have a seperate warranty)

Hassle free 30 day return policy  

Works with all water heaters including Tankless

See reviews here http://floridaecoproducts.com/Product_Reviews.html